Free kitchen appliance user manuals, instructions, and product support information. Find owners guides and pdf support documentation for blenders, coffee makers, juicers and more. GE Water Dispenser GXCF05D User Guide ManualsOnline.com. GE® ENERGY STAR® Qualified Hot and Cold Free-Standing Water Dispenser with Storage Compartment. GE® ENERGY STAR® Qualified Hot and Cold Free-Standing Water Dispenser with Storage Compartment GXCF05D. Bvseosdk, javasdk, bvseo-3.2.0; CLOUD, getAggregateRating, 37ms. GE has determined that this product meets the ENERGY STAR. The dispenser. Remove the water bottle from the dispenser. Put a container that will withstand hot water under the hot water tap. Press the hot dispenser button until the water is cool (about 1 quart). Add water to the cold water reservoir (on top where the bottle supplies water) as needed.
Care and cleaning of the dispenser.
IMPORTANT: Set both power switches (on the
back of the dispenser) in the 0 (off) position and
unplug the water dispenser before cleaning.
The inside and outside of the cabinet can
be washed with mild soap and water. Rinse
thoroughly with clear water. Never use
commercial cleaners or abrasive scouring
powders.
Sweep away or vacuum any dust from the
condenser coils on the back of the unit. For
best results, use a brush specially designed for
this purpose. It is available at most appliance
stores.
Cleaning the Outside and Storage Cabinet
(on some models)
The dispenser drip tray is not self-draining.
To reduce water spotting or deposits, the tray
and its grille should be emptied, cleaned and
wiped dry regularly.
Clean with mild soap or on the top rack in
the dishwasher.
Cleaning the Drip Tray and Grille
Drip
tray
Drip tray grille
Draining the Dispenser
The dispenser should be drained before cleaning the tanks and before leaving for long vacations or absences.
Drain outlet cap
Floor models
(rear of dispenser)
Floor Models
1.
Set both power switches (on the back of the dispenser) in the
0 (off) position and unplug the dispenser.
2.
Remove the water bottle from the dispenser.
3.
Put a container that will withstand hot water under the hot
water tap. Press the HOT dispenser button until the water is
cool (about 1 quart).
Add water to the cold water reservoir
(on top where the bottle supplies water) as needed.
4.
Dispense water from both buttons into container(s) until
no more water can be dispensed (about 1 quart of water still
remains in the dispenser).
5.
Place a large bucket beneath the drain outlet on the rear of
the dispenser.
6.
Using a Phillips screwdriver, loosen the screws on the bracket
covering the drain outlet cap. Rotate the bracket out of the way
to allow access to the cap.
7.
Remove the cap and silicon stopper from the drain outlet and
and allow water to drain. After draining, replace the stopper
and cap.
8.
Rotate the bracket back into place and tighten screws.
Make sure to install a full bottle and dispense water from the
hot water tap before plugging in and turning on the dispenser
(see Loading the Dispenser).
Countertop Models
1.
Set both power switches (on the back of the dispenser) in the
0 (off) position and unplug the dispenser.
Ge Profile Water Dispenser Manual
2.
Remove the water bottle from the dispenser.
3.
Put a container that will withstand hot water under the hot
water tap. Press the HOT dispenser button until the water is
cool (about 1 quart).
Add water to the cold water reservoir
(on top where the bottle supplies water) as needed.
4.
Dispense water from both buttons into container(s) until
no more water can be dispensed (about 1 quart of water still
remains in the dispenser).
Ge Water Dispenser Model Gxcf05d
WARNING:
Lift the dispenser carefully; it weighs
approximately 40 lbs (18 kg). Avoid accidentally pressing the
dispenser buttons while lifting or carrying.
5.
Place the dispenser over a sink with 3 feet on the counter.
Hold or secure the dispenser steady while removing the
retaining clip and drain cover. Remove the retaining clip and
drain cover from the drain outlet, making sure not to damage
the drain cover. Allow water to drain.
6.
After draining, replace the drain cover and retaining clip.
Make sure to install a full bottle and dispense water from the
hot water tap before plugging in and turning on the dispenser
(see Loading the Dispenser).
5
Drain cover and
retaining clip
Countertop models
(bottom of dispenser)